How To Measure Air Quality

Like all things, we can measure air quality scientifically. We can get a number that says just how gross the air in your facility is. Not only that, but we can figure out what particular type of problem your air has. There’s more to air quality than just saying it’s good or bad. The Troublemakers There are three commonly examined areas for air quality. We have different ways to detect and measure each of them, but these are typically available all in one tool or device. Particulate Matter There are tiny particles in the air, often harmful chemicals we don’t notice individually. Think of things like the exhaust from a car. That exhaust is made of billions of tiny particles of burned fuel and even metal shavings from the engine. These can have negative health effects. Particulates from cars could play a role in Alzheimers Disease. These can detect bacteria, viruses, and mold as well. Sensors for these are rated in their measuring sizes, 2.5 microns and below, 10 microns and below, etc. Your hair is about 40-70 microns thick, for comparison. Volatile Organic Compounds The rule of thumb is that a VOC is something you smell and notice. That’s not always the case, but it’s a good guiding post. These chemicals are highly reactive, dangerously so. Examples of these are things like cleaning chemicals, gasoline, and paint. They’re things you should try not to breathe in. Carbon Dioxide This […]

Read More →

Carbon Monoxide Detectors

Last week we covered how a draft inducer and it’s attached pressure sensor can help prevent Carbon Monoxide from leaking out of a furnace. This week we’re moving up to the next line of defense: a dedicated Carbon Monoxide Detector. These are often installed in new homes and offices as required by local building codes in most of the United States. Where they’re not installed by construction, they’re usually installed by the facility’s owner as a precaution.   What’s the Big Deal? Carbon Monoxide is one of the deadliest, common compounds in the world. It’s is a colorless, odorless gas that will kill you at the right concentrations. There’s only two ways for someone to know they’ve been exposed to a harmful dose: Use a detector or Recognise the Symptoms before it’s too late. The initial symptoms include headache, dizziness, weakness, vomitting, chest pain, and confusion. In large part, these common symptoms can be attributed to hundreds of other ailments, including the common flu. Greater exposure can lead to passing out, arrhythmia, seizures, and death. Even then, there will be longterm complications, including memory problems, movement disabilities, and fatigue. Most people are not able to detect and react to these symptoms as Carbon Monoxide poisoning before it’s too late. They’re often waived off as a flue or some other lesser problem until it’s too late.   How Do We Detect An Invisible, Colorless, Odorless Gas? While Carbon Monoxide itself is […]

Read More →

Preventing CO2 Poisoning with Pressure

We have rollout switches and temperature sensors to prevent fires from spreading beyond the furnace. What about exhaust gasses? Almost every heating fuel we use produces deadly gasses. CO2, NO2, and more. If these gasses escape your furnace, you’re either going to leave the building or be killed by the gasses. It’s essential that we keep these gasses away from you. Your furnace has some very interesting ways of doing this and detecting a deadly hardware failure.   The Draft Inducer Older furnaces rely on physics and chemistry to get the CO2 out. As your furnace runs, it creates hot gasses. The hotter a gas is, the higher it rises in the atmosphere. As long as the exhaust is hot, it should rise up into your chimney or exhaust flue and be vented safely outside away from people. This isn’t entirely ideal, the exhaust is limited by the temperature difference, slowing it down. It’s possible for wind and other atmospheric conditions to disrupt the exhaust flow. There’s no mechanism to detect and respond to a blocked exhaust path. Modern furnaces don’t let the hot gasses just meander out the chimney. We use Draft Inducers, essentially blowers built just for furnace exhaust. These little blowers kick on a minute before ignition to vent the combustion chamber and usually remains on until after the furnace has shutdown. On the surface, this just makes the furnace burn cleaner. If there’s less carbon dioxide […]

Read More →

Introduction to Fire Alarms

Automation is essential in our industry. We have machines that regulate our air temperature, that provide a constant supply of hot and cold water, that control massive industrial processes, and more. Employees, clients, and managers want to just walk in, be comfortable, and get to work. We all overlook one of the most essential, automated things we have: the Fire Safety System.     Old Fire Safety The hardware we use for safety today has a remarkably long history. Fire suppression can be traced at least as far back as Leonardo Da Vinci, who’s sprinkler system essentially washed away an entire kitchen. Fire alarms go back to the 1600s, when there were literal patrols in search of fire, much as police patrol in search of crime or emergencies. Overtime, there were systems of telegraphs used for fire alarms and gun powder triggered sprinklers. These older systems spread for their insurance benefits. A building with a sprinkler system would have significantly cheaper insurance rates. It would ultimately pay for itself. The difference between sprinklers and no sprinklers is that significant.   Modern Fire Safety Today, things are more extensive. Telegraph alarm systems and gun powder sprinklers gave way to extensive electronics that interact with every single part of your building. It all starts with the sensors and detectors. In a modern system, every single smoke detector has a unique ID and name in the system. If the elevator maintenance room detector […]

Read More →